EnGenius EOA7530 Manual do Utilizador

Dual Radio Concurrent AP/CB EOA7530 User Manual Version : 1.0

9 3 Computer Configuration Instruction 3.1 Obtain an IP Automatically In order to configure EOA7530, please follow the instruction below: 1. In the

10 3.2 Logging Method After complete the IP settings from last section, you can now access the web-based configuration menu. 1. Open web browser 2.

11 4 Wireless Configuration 4.1 Switching Operation Mode The EOA7530 supports 3 different operation modes: Access Point, Client Bridge, and Client Rou

12 Note: If you would like to use the Access Point mode in both 5G and 2.4G network, please check next section for details. 4.1.2 Dual Mode Only Acce

13 4.2.1 Access Point Mode (Dual Mode) Radio Select the radio button to enable or disable wireless function. Enable SSID# EOA7530 can support up to 4

14 Apply / Cancel Press Apply to apply the changes or Cancel to return previous settings. Auction: Both 5G and 2.4G bands are using the same SSID. 4.

15 4.2.3 Access Point Mode (2.4G) Radio Select the radio button to enable or disable wireless function. Enable SSID# EOA7530 can support up to 4 diff

16 4.2.4 Client Bridge Mode/Client Router Mode (Dual Mode) ESSID Specify the SSID is given by Access Point if known. Otherwise, you may use Site Surv

17 4.2.5 Client Bridge Mode/Client Router Mode (5G) ESSID Specify the SSID is given by Access Point if known. Otherwise, you may use Site Survey to s

18 Note: For more details of Site Survey, please refer to the Site Survey section. 4.3 Site Survey Use this feature to scan nearby Access Point. N

1 Table of Contents 1 PRODUCT OVERVIEW ...

19 We are strongly recommended that uses WPA2-PSK AES as your security settings. 4.5.1 WEP (Access Point) ESSID Selection EOA7530 supports up to 4 di

20 4.5.2 WEP (Client Bridge / Client Router) Network Name (SSID) Specify the Access Point’s SSID that you would like to associate with. Encryption Se

21 4.5.3 WPA pre-shared Key (Access Point) ESSID Selection EOA7530 supports up to 4 different SSIDs. Each SSID can be set to different authentication

22 4.5.4 WPA pre-shared Key (Client Bridge / Client Router) Network Name (SSID) Specify the Access Point’s SSID that you would like to associate with

23 4.5.5 Radius (Access Point Only) Radius authentication type is only available in Access Point Mode. Use this feature if you have Radius Server. It

24 4.6 Wireless Advanced Settings If you do not have experience with Wireless Advanced Settings, we suggest remain all settings to default. Any modif

25 sometimes cause unable to connect to the network. On the other hand, the lower transmit power will cause client unable to connect to the device. Di

26 4.7 Wireless Access Control List Wireless Access Control List is used to Allow or Deny wireless clients by their MAC addresses, accessing the Netw

27 5.1 LAN Settings Auction: Changing LAN IP Address will change LAN Interface IP address. Webpage will automatically redirect to the new IP address a

28 5.2 DHCP Info Click on the DHCP Info link under the TCP/IP section. This page displays the list of Clients that are associated to the EOA3630 throu

2 5 LAN SETUP ...

29 5.3 SNMP Settings SNMP Enable Select the Radio button to enable SNMP feature. SNMP Disable Select the Radio button to disable SNMP feature. Apply

30 6 Internet Settings 6.1 DHCP (Dynamic IP) Select Dynamic IP as your WAN connection type to obtain your IP address automatically. You will need to e

31 6.3 PPPoE (Point-to-Point Protocol over Ethernet) Select PPPoE as your WAN connection type if your ISP provides Username and Password. PPPoE is a D

32 6.4 PPTP (Point-to-Point Tunneling Protocol) Select PPTP as your WAN connection type if your ISP provides information about IP Address, Subnet Mask

33 Login Specify the Username that is given by your ISP. Password Specify the Password that is given by your ISP. Service IP Address Specify the Serv

34 7 Information Status Status section is used to check the status of device information such as System up time, Firmware version, Wireless Client Lis

35 7.2 Wireless Client List Click on the Client List link under the 5G/2.4G Wireless section. This page displays the list of Clients that are associat

36 7.4 Internet Status Click on the Status link under the Internet section. This page displays the current connection type status of the network, incl

37 8 Management Settings Management section is on the navigation drop-down menu. This section can help you to manage your device and adjust system set

38 NTP Time Server Specify the NTP Server’s Domain name or IP Address. Daylight Saving Place a Check to enable Daylight Saving feature. Configure the

3 1 Product Overview Thank you for using EOA7530. EOA7530 is a dual core wireless outdoor Access Point/Client Bridge. It is a powerful, enhanced, ent

39 8.4 Remote Control Host Address Specify the IP Address you would like to use as your remote controller. Port Specify the Port number. Enable Place

40 Restore to Factory Default Settings Click on Reset button to reset all the settings to the default values. Backup Settings Click on Save to save c

41 9 Network Configuration Example This chapter describes the role of the EOA7530 with three different modes. The Access Point mode’s default configu

42 Step3 Select 5G or 2.4G as your wireless mode. Step4 Use site survey to scan nearby Access Point and select the certain AP you would like to conne

43 Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comp

4 Network managers in dynamic environments can minimize the overhead caused by moves, extensions to networks, and other changes with wireless LANs. f)

5 PPPoE/PPTP function support (CR mode) Easy to access internet via ISP service authentication 1.2 Feature Dual Mode Use this feature to configure 2.

6 1.3 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials

7 2 EOA7530 Multi-Function Instruction Guide 2.1 Access Point In the Access Point Mode with WDS Function, EOA7530 function likes a central connection

8 2.3 Client Router In the Client Router Mode, the EOA7530 has DHCP Server build inside that allows many LANs automatically generate an IP address to